Pyle PLA4600D - 4600 Watt Monoblock Class-D Amplifier

You looking to find the "Pyle PLA4600D - 4600 Watt Monoblock Class-D Amplifier" Good news! You can purchase Pyle PLA4600D - 4600 Watt Monoblock Class-D Amplifier with secure price and compare to view update price on this product. And deals on this product is available only for limited time.

Price: $189.28 $173.67   

Product Feature

• Class D Monoblock Power Amplifier - Mono Block Sub woofer Amplifier - PWM ( Pulse-Width-Modulation ) System - Variable Subsonic Filter ( 15Hz - 55Hz 24dB / Octave) - Advanced Protection Circuitry
• RMS Power @ 4 Ohms: 1 x 1200W - Frequency Response 15 Hz-150 Hz (±3dB) - Glass Epoxy PCB - Phase Control 0-180 Degree - S/N Ratio: >90dB
• RMS Power @ 2 Ohms: 1 x 1800W - Output Power @ 14.4v DC, 50Hz - Silver RCA Inputs - Remote Bass Boost - Dimensions:10.24''W x 2.21''H x 14.58''L
• RMS Power @ 1.3 Ohms: 1 x 2400W - 1 Ohm Stable - Custom Terminal Block for Speaker Connection - Input Impedance: 10K Ohms
• Maximum Power Output 4600W Mono - MOSFET Power Supply - Thermal / Overload / Short Circuit Protection - Soft Turn On/ Off
• Class D Monoblock Power Amplifier
• RMS Power @ 4 Ohms: 1 x 1200W
• RMS Power @ 2 Ohms: 1 x 1800W
• RMS Power @ 1.3 Ohms: 1 x 2400W
• Maximum Power Output 4600W Mono
• Mono Block Sub woofer Amplifier
• Frequency Response 15 Hz-150 Hz (� 3dB)
• Output Power @ 14.4v DC, 50Hz
• 1 Ohm Stable
• MOSFET Power Supply
• PWM ( Pulse-Width-Modulation ) System
• Glass Epoxy PCB
• Silver RCA Inputs
• Custom Terminal Block for Speaker Connection
• Thermal / Overload / Short Circuit Protection
• Variable Subsonic Filter ( 15Hz - 55Hz 24dB / Octave)
• Phase Control 0-180 Degree
• Remote Bass Boost
• Input Impedance: 10K Ohms
• Soft Turn On/ Off
• Advanced Protection Circuitry
• S/N Ratio: >90dB
• Dimensions:10.24''W x 2.21''H x 14.58''L
• Sold as : Unit

Product Description

When power isn’t enough, you need Pyle Power. And our D-series feature Class-D digital amplifiers, which greatly reduce power consumption and heat while increasing sound levels for an overall major boost in efficiency. The PLA4600D is a 4600-watt class-D monoblock amplifier. It� �s equipped with everything you� ve come to expect from quality car amplifiers. The RCA ports are silver-plated for eliminating signal loss. A subsonic filter allows low-end interference to be cut, so your speakers will always be delivered the highest quality audio. The MOSFET pulse width modulation power supply allows for a clean, distortion-free signal to your speakers. To keep both your car and the amplifier safe, this model is equipped with thermal, overload, and short circuit protection. So when what you need is power, trust Pyle Power.

Pyle PLA4600D - 4600 Watt Monoblock Class-D Amplifier Review

Having suffered a long time without a proper amplifier, (Power Acoustik Crypt Series, 2000W Mono-block outputs fried in 8 months, leaving my two 12 inch Infinity subs cold and neglected) I found this. Initially worried it wouldn't change a thing, I hooked it up quickly (inputs for power, and speakers are at a near 45 degree angle, making it nice to not have to pull the entire amp/box out to re-wire) with better sound quality than the Power Acoustik amp, or any I have had prior.

It has good safety specs (Short circuit, thermal and overload protection), a pretty comprehensive sound control layout (turn dials for HPF, LPF, crossover controls for full range, LPF, and HPF, and gain and bass knobs) and a sleek, small look that is nice just to look at. It also boasts that it is bridgeable, which I don't really need to do but with most amps, bridging either void warranties or it isn't recommended by the manufacturer.

The only minor faults are that the protection/power light are on the rear, making it hard to check unless opening my trunk. Additionally, the turn dials are fit to be turned with a phillips screwdriver, rather than a flathead- which will only make it a little longer (maybe 5 seconds) of a process if you don't remember where you set the dials. Also, using one speaker sounds a hell of a lot better- with two it almost sounds like they are reverse phased.

I see a lot of bad reviews for fire, and overheating. Usually blown fuses are a problem in the wiring that you yourself do. The music I listen to has a wide range of highs and lows, mainly Nine Inch Nails, and scores for films by Marco Beltrami (The score for Scream is a prime example), and it makes them sound like a whole new listening experience.

Other bad reviews claim that the amp is underpowered compared to what it is rated at. Almost every amplifier is, my 2000W monoblock only pushed 860W RMS. Educate yourself, please. Products like Sony, and Pioneer are 'higher end' and do the same thing, with their subwoofers, head units, and amps. If you dont get 1000W(!!!) per speaker, save your money and busy a $500 3000W Rockford Fosgate or something.

I heard a lot of good things about Pyle and now I will also be singing their praises. It's hard enough to find a reliable, cheap 2-ohm amp, let a lone one that is as sleek, safe, and convenient as this one is. Thumbs up.

Most of the consumer Reviews tell that the "Pyle PLA4600D - 4600 Watt Monoblock Class-D Amplifier" are high quality item. You can read each testimony from consumers to find out cons and pros from Pyle PLA4600D - 4600 Watt Monoblock Class-D Amplifier ...